Bảng mạch sạc pin năng lượng mặt trời Mini CN3065 500Ma cho Arduino
1 Đánh Giá
7 Đã Bán
37
25.000 đ
Xem sản phẩm trên ShopeeQuốc tế
thứ hai 15/11/2021 lúc 04:22 CH
500Ma Mini Solar Lipo Charger Board CN3065 Lithium Battery Charge Chip DIY Outdoor Charging Board Module For Arduino
This is a supper mini Solar Lipo charger based on the CN3065 - a single lithium battery charge management chip.
This Solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is easy as well, just plug your solar panel into one side of the Solar charger and your battery into the other and you are good to start charging!
The output of the Solar Charger is intended to charge a single polymer lithium ion cell. The load should be connected in parallel with the battery. By default, the Solar charge comes set to a maximum charge current of 500mA with a maximum recommended input of 6V (minimum 4.4V). It's recommended that batteries not be charged at greater than their capacity rating.
Features:
Solar panel input: 4.4-6V
Max charge current: 500Ma
Interface: 2-pin JST connectors(or PH2.0)
Short circuit protection
Continuous Charge Current Up to 500mA
Battery status indication ( Red : Charging , Green: Charged )
Micro-USB Connector
Package Included:
1pcs * 500Ma Mini Solar Lipo Charger Board CN3065
Before purchase:
1. All the goods are in stock and we will dispatch immediately if we receive the order.
2.Please read the item description, if you have any question, do not hesitate to contact us.
Shipment：
1.1-2 days to ship(except for the pro-order item)
After purchase:
1.If you are satisfied，please give us 5 stars praise.
2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems.
if you receive a defect item,please contact us at once with item picture or video
#500Ma #Mini #Solar #Lipo #Charger #Board #CN3065 #Lithium #Battery #Charge #Chip #DIY #Outdoor #Charging #Board #Module #For #Arduino
This is a supper mini Solar Lipo charger based on the CN3065 - a single lithium battery charge management chip.
This Solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is easy as well, just plug your solar panel into one side of the Solar charger and your battery into the other and you are good to start charging!
The output of the Solar Charger is intended to charge a single polymer lithium ion cell. The load should be connected in parallel with the battery. By default, the Solar charge comes set to a maximum charge current of 500mA with a maximum recommended input of 6V (minimum 4.4V). It's recommended that batteries not be charged at greater than their capacity rating.
Features:
Solar panel input: 4.4-6V
Max charge current: 500Ma
Interface: 2-pin JST connectors(or PH2.0)
Short circuit protection
Continuous Charge Current Up to 500mA
Battery status indication ( Red : Charging , Green: Charged )
Micro-USB Connector
Package Included:
1pcs * 500Ma Mini Solar Lipo Charger Board CN3065
Before purchase:
1. All the goods are in stock and we will dispatch immediately if we receive the order.
2.Please read the item description, if you have any question, do not hesitate to contact us.
Shipment：
1.1-2 days to ship(except for the pro-order item)
After purchase:
1.If you are satisfied，please give us 5 stars praise.
2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems.
if you receive a defect item,please contact us at once with item picture or video
#500Ma #Mini #Solar #Lipo #Charger #Board #CN3065 #Lithium #Battery #Charge #Chip #DIY #Outdoor #Charging #Board #Module #For #Arduino